Ballast
1.Maximum weight 6300
2. Hanging weights are permitted. No more than 12” for grill to weights
3. All weights must be securely fastened.
4. No weight allowed in cab
Chassis and Suspension
1.OEM Chassis is mandatory. The vehicle must retain OEM frame rails
2.Must maintain OEM measurements for cab and bed being used. .
3.Rear suspension may block solid. Must have travel to be solid
4.Stock style suspension must be in place. Stock style refers to the type of
suspension that came from the manufacturer in the year/make/model/vintage
of the vehicle being pulled. Must have leaf spring.
5.Hydraulic over electric is permitted But must run through OEM steering box
6. Must have an OEM steering column.
Battery
Batteries are not allowed in the cab, unless factory installed. Must be in OEM location
Dress Code
1.Dot helmet is highly recommended
2. Leather shoes ,Long Pants, and Jacket or Long Sleeve Shirt required
3. Fire suits are highly recommended
Body
1.The body must replicate the OEM truck body including the full bed floor. The body
must retain the full sheet metal. No mud flaps or dirt deflector
2. The complete OEM floor pan is mandatory. Vehicle must maintain a complete
firewall
3. Must here all windows, Must have all working OEM lights, Must have all
interior panels and dashboard.
4. Flatbeds are permitted and must be manufactured. No homemade beds are
allowed.
Exhaust
1.Exhaust must clear the center of the cab
2.Aftermarket exhaust is permitted.
3.Headers are allowed.
4.Exhaust through the hood is not permitted.
Safety Equipment
1.All trucks must have at least six-inch-wide u-joint shield around the rear u-joint
constructed of at least 5/16-inch steel or 3/8 aluminum . All shields must be
securely mounted to the vehicle.
2.Any front shaft u-joints that can be visibly seen
from side of truck must be shielded to contain the u-joint and the end of the
driveshaft. Must have one center loop
3.Safety switch must kill the fuel and the ignition. Switch will be securely mounted
to the rear of the vehicle. A 2 inch or bigger solid ring must be attached to end of
switch. Switch must also be able to be activated in cab while driver is secured
in the vehicle.
4.All vehicles must have a 2 1/2 lb. dry chemical within the reach of the driver.
5.Seatbelts are required to go hook to the sled.
6.Must have a working back up light.
Drive Line
1.OEM rear and front ends required. Must have come factory in a one ton or
smaller vehicle.
2.OEM transmission and transfer case must be used. Must have come factory in a
one ton or smaller vehicle
3.SFI bell housing and/or SFI blow proof bell housing or SFI blanket type shield
must be used. Slipper clutches are allowed
4.Automatic transmissions must be covered 360 degrees from back of engine block
to the tall shaft bolts
Tires
1.Tires must be DOT approved no larger than 35x12.50. or 315x75 Metric
2.Must have factory tire size stamped for verification. If size is removed they will be
considered illegal.
3. No studded tires or tire chains. No alterations to tires permitted. No bar tires
4. Rear tires must track 50% over the path of front tires.
5. Any aftermarket wheels permitted
Fuel
1.Gasoline
2.Racing fuel allowed
3.No propane or Nitrous
4. Other oxygen enhancers are not allowed
Brakes
Must have four working brakes,
Must have working brake lights
Engine
418 cubic inch limit or less for small block
419 cubic inch and up considered big block
1. Engine must be in OEM location
2. Aluminum heads are permitted. No pro stock style heads.
3. Aluminum block permitted must be OEM
4. Any single naturally aspirated carburetor allowed
5. EFI fuel injection is permitted Must be OEM
6. Intake must be cast iron or aluminum only
7. No tunnel rams are allowed
8. Engine driven fans require 360 metal shielding . Electric fans are permitted
9. Aftermarket radiators are permitted . Must be in an OEM location. Must flow
coolant freely
10.Blow proof harmonic balancer or 360 shield highly recommended
Hitch
1. Must be Reese style hitch. May be reinforcement. Must not extend forward of
the rear axle.
2. Must be rigged in all directions, Hitch mounting point can not be above frame
rails And stationary in all directions
3. No drawbar hitch or trick hitches allowed
4. Hook point must be at the rear most point of the vehicle. and most rearward of
stock location of the tailgate.
5. Maximum hitch height of SMALL BLOCK 26” with a minimum of 3.75”x3”
opening.
6.Maximum hitch height of BIG BLOCK 24” with a minimum of 3.75”x3” opening.
7. Hitch must be on a level plane with the ground.
1.Maximum weight 6300
2. Hanging weights are permitted. No more than 12” for grill to weights
3. All weights must be securely fastened.
4. No weight allowed in cab
Chassis and Suspension
1.OEM Chassis is mandatory. The vehicle must retain OEM frame rails
2.Must maintain OEM measurements for cab and bed being used. .
3.Rear suspension may block solid. Must have travel to be solid
4.Stock style suspension must be in place. Stock style refers to the type of
suspension that came from the manufacturer in the year/make/model/vintage
of the vehicle being pulled. Must have leaf spring.
5.Hydraulic over electric is permitted But must run through OEM steering box
6. Must have an OEM steering column.
Battery
Batteries are not allowed in the cab, unless factory installed. Must be in OEM location
Dress Code
1.Dot helmet is highly recommended
2. Leather shoes ,Long Pants, and Jacket or Long Sleeve Shirt required
3. Fire suits are highly recommended
Body
1.The body must replicate the OEM truck body including the full bed floor. The body
must retain the full sheet metal. No mud flaps or dirt deflector
2. The complete OEM floor pan is mandatory. Vehicle must maintain a complete
firewall
3. Must here all windows, Must have all working OEM lights, Must have all
interior panels and dashboard.
4. Flatbeds are permitted and must be manufactured. No homemade beds are
allowed.
Exhaust
1.Exhaust must clear the center of the cab
2.Aftermarket exhaust is permitted.
3.Headers are allowed.
4.Exhaust through the hood is not permitted.
Safety Equipment
1.All trucks must have at least six-inch-wide u-joint shield around the rear u-joint
constructed of at least 5/16-inch steel or 3/8 aluminum . All shields must be
securely mounted to the vehicle.
2.Any front shaft u-joints that can be visibly seen
from side of truck must be shielded to contain the u-joint and the end of the
driveshaft. Must have one center loop
3.Safety switch must kill the fuel and the ignition. Switch will be securely mounted
to the rear of the vehicle. A 2 inch or bigger solid ring must be attached to end of
switch. Switch must also be able to be activated in cab while driver is secured
in the vehicle.
4.All vehicles must have a 2 1/2 lb. dry chemical within the reach of the driver.
5.Seatbelts are required to go hook to the sled.
6.Must have a working back up light.
Drive Line
1.OEM rear and front ends required. Must have come factory in a one ton or
smaller vehicle.
2.OEM transmission and transfer case must be used. Must have come factory in a
one ton or smaller vehicle
3.SFI bell housing and/or SFI blow proof bell housing or SFI blanket type shield
must be used. Slipper clutches are allowed
4.Automatic transmissions must be covered 360 degrees from back of engine block
to the tall shaft bolts
Tires
1.Tires must be DOT approved no larger than 35x12.50. or 315x75 Metric
2.Must have factory tire size stamped for verification. If size is removed they will be
considered illegal.
3. No studded tires or tire chains. No alterations to tires permitted. No bar tires
4. Rear tires must track 50% over the path of front tires.
5. Any aftermarket wheels permitted
Fuel
1.Gasoline
2.Racing fuel allowed
3.No propane or Nitrous
4. Other oxygen enhancers are not allowed
Brakes
Must have four working brakes,
Must have working brake lights
Engine
418 cubic inch limit or less for small block
419 cubic inch and up considered big block
1. Engine must be in OEM location
2. Aluminum heads are permitted. No pro stock style heads.
3. Aluminum block permitted must be OEM
4. Any single naturally aspirated carburetor allowed
5. EFI fuel injection is permitted Must be OEM
6. Intake must be cast iron or aluminum only
7. No tunnel rams are allowed
8. Engine driven fans require 360 metal shielding . Electric fans are permitted
9. Aftermarket radiators are permitted . Must be in an OEM location. Must flow
coolant freely
10.Blow proof harmonic balancer or 360 shield highly recommended
Hitch
1. Must be Reese style hitch. May be reinforcement. Must not extend forward of
the rear axle.
2. Must be rigged in all directions, Hitch mounting point can not be above frame
rails And stationary in all directions
3. No drawbar hitch or trick hitches allowed
4. Hook point must be at the rear most point of the vehicle. and most rearward of
stock location of the tailgate.
5. Maximum hitch height of SMALL BLOCK 26” with a minimum of 3.75”x3”
opening.
6.Maximum hitch height of BIG BLOCK 24” with a minimum of 3.75”x3” opening.
7. Hitch must be on a level plane with the ground.